copyright@ semipower electronic technology co., ltd. all rights reserved. may. 2014. rev.1.0 features high ruggedness r ds( on ) (max1.25 ? )@v gs =10v gate charge (typical 19 nc) improved dv/dt capability 100% avalanche tested n - channel to - 220 mosfet absolute maximum ratings thermal characteristics symbol parameter value unit r thjc thermal resistance, junction to case 5.3 o c/w r thcs thermal resistance, case to sink o c/w r thja thermal resistance, junction to ambient 48.2 o c /w 1/5 bv dss : 600v i d : 7a r ds(on) :1.25 1 2 3 SW7N60R samwin item sales type marking package packaging 1 sw p 7n60 SW7N60R to - 220 tube order codes symbol parameter value unit v dss drain to source voltage 600 v i d continuous drain current (@t c =25 o c) 7* a continuous drain current (@t c =100 o c) 4.4* a i dm drain current pulsed (note 1) 28 a v gs gate to source voltage 30 v e as single pulsed avalanche energy (note 2) 453 mj e ar repetitive avalanche energy (note 1) 117 mj dv/dt peak diode recovery dv/dt (note 3) 5 v/ns p d total power dissipation (@t c =25 o c) 23.8 w derating factor above 25 o c 0.2 w/ o c t stg , t j operating junction temperature & storage temperature - 55 ~ + 150 o c t l maximum lead temperature for soldering purpose, 1/8 from case for 5 seconds. 300 o c general description this power mosfet is produced with advanced vdmos technology of samwin . this technology enable power mosfet to have better characteristics, such as fast switching time, low on resistance, low gate charge and especially excellent avalanche characteristics . this power mosfet is usually used at high efficient dc to dc converter block and switch mode power supply . *. drain current is limited by junction temperature. 1. gate 2. drain 3. source 1 2 3 to - 220
copyright@ semipower electronic technology co., ltd. all rights reserved. may. 2014. rev.1.0 electrical characteristic ( t c = 25 o c unless otherwise specified ) symbol parameter test conditions min. typ. max. unit off characteristics bv dss drain to source breakdown voltage v gs =0v, i d =250ua 600 v bv dss / t j breakdown voltage temperature coefficient i d =250ua, referenced to 25 o c 0.78 v/ o c i dss drain to source leakage current v ds =600v, v gs =0v 1 ua v ds =480v, t c =125 o c 50 ua i gss gate to source leakage current, forward v gs =30v, v ds =0v 100 na v gs = - 30v, v ds =0v - 100 na gate to source leakage current, reverse on characteristics v gs(th) gate threshold voltage v ds =v gs , i d =250ua 2 4 v r ds(on) drain to source on state resistance v gs =10v, i d =3.5a 0.9 1.25 ? g fs forward transconductance v ds = 30v, i d =3.5 a 4.5 s dynamic characteristics c iss input capacitance v gs =0v, v ds =25v, f=1mhz 943 pf c oss output capacitance 110 c rss reverse transfer capacitance 1.7 t d(on) turn on delay time v ds =300v, i d =7a r g =25? (note 4 5 ) 15 ns tr rising time 27 t d(off) turn off delay time 43 t f fall time 29 q g total gate charge v ds =480v, v gs =10v, i d =7a (note 4 5 ) 19 nc q gs gate - source charge 6 q gd gate - drain charge 6 source to drain diode ratings characteristics symbol parameter test conditions min. typ. max. unit i s continuous source current integral reverse p - n junction diode in the mosfet 7 a i sm pulsed source current 28 a v sd diode forward voltage drop. i s =7a, v gs =0v 1.5 v t rr reverse recovery time i s =7a, v gs =0v, di f /dt=100a/us 330 ns q rr reverse recovery charge 3.2 u c . notes 1. repeatitive rating : pulse width limited by junction temperature. 2. l = 18.5mh, i as = 7a, v dd =100 v, r g =25?, starting t j = 25 o c 3. i sd 7a, di/dt = 100a/us, v dd bv dss , staring t j =25 o c 4. pulse test : pulse width 300us, duty cycle 2% 5. essentially independent of operating temperature. samwin 2/5 SW7N60R
copyright@ semipower electronic technology co., ltd. all rights reserved. may. 2014. rev.1.0 fig. 1. on - state characteristics fig. 2. on - resistance variation vs. drain current and gate voltage fig. 3. gate charge characteristics 3/5 samwin SW7N60R fig. 6. on resistance variation vs. junction temperature fig 5. breakdown voltage variation vs. junction temperature fig. 4. on state current vs. diode forward voltage
copyright@ semipower electronic technology co., ltd. all rights reserved. may. 2014. rev.1.0 4/5 samwin SW7N60R fig. 7. maximum safe operating area fig. 8. transient thermal response curve fig. 9. c apacitance characteristics fig. 10. gate charge test circuit & waveform v ds same type as dut dut v gs 2ma q g q gs q gd v gs charge nc 10v
copyright@ semipower electronic technology co., ltd. all rights reserved. may. 2014. rev.1.0 v dd dut v ds r l r gs 10v in 10% v ds v in 90% 10% t d(on) t r t on t d(off) t off t f fig. 11. switching time test circuit & waveform fig. 12. unclamped inductive switching test circuit & waveform 5/5 samwin SW7N60R fig. 13. peak diode recovery dv/dt test circuit & waveform v dd same type as dut v ds l r g 10v gs i s + - v ds dut *. dv/dt controlled by rg *. is controlled by pulse period v gs (driver) i s (dut) v ds (dut) body diode forward voltage drop v f diode recovery dv/dt i rm di/dt 10v diode reverse current v dd
|
